Decomposition of Carbon Dioxide to Carbon with Active Wustite at 300°C

Active wustite (FeδO, with a δ value of 0.98) was prepared by keeping normal wustite (δ value of 0.94) in a N₂ atmosphere at 300°C for 10 min. This reaction is given by (4δ₂–3)Fe_δ1O→(4δ₁–3)Fe_δ2O + (δ₂–δ₁)Fe₃O₄ where δ₁= 0.94 and δ₂= 0.98. The equation indicates that the normal wustite undergoes eutectoid decomposition into active wustite and stoichiometric magnetite (Fe₃O₄). Carbon dioxide (1.013 × 10⁵ Pa) was almost completely (100%) decomposed into carbon (zero valence) by the active wustite at the low temperature of 300°C, which was associated with the transformation of the active wustite into the stoichiometric magnetite. The internal pressure of the reaction cell eventually became a vacuum.     

High-Temperature Active Oxidation of Chemically Vapor-Deposited Silicon Carbide in CO─CO2 Atmosphere

Active oxidation behavior of CVD-SiC in CO─CO₂ atmospheres was investigated using a thermogravimetric technique in the temperature range between 1823 and 1923 K. The gas pressure ratio, P _CO2/ P _CO, was controlled between 10⁻⁴ and 10⁻¹ at 0.1 MPa. Active oxidation rates (mass loss rates) showed maxima at a certain value of P _CO2/ P _CO, ( P _CO2/ P _CO )^*, In a P _CO2/ P _CO region lower than the ( P _CO2/ P _CO)^* a carbon layer was formed on the SiC surface. In a P _CO2/ P _CO region higher than the ( P _CO2/ P _CO)^*, silica particles or a porous silica layer was observed on the SiC surface.     

Autoxidation of ethyl eicosapentaenoate and docosahexaenoate

The extent of oxidation of ethyl esters of eicosapentaenoic (EPA) and docosahexaenoic acids (DHA) was compared quantitatively with that of ethyl linoleate (Lo) and ethyl linolenate (Ln) by oxygen uptake and formation of conjugated diene, hydroperoxide and secondary oxidation products. EPA and DHA esters were oxidized rapidly even at 5 C in the dark after an induction period of 3–4 days, while the induction periods of Ln and Lo esters were 20 days and more than 60 days, respectively. Oxygen uptake of EPA and DHA esters after the induction period was 5.2 and 8.5 times faster than that of ethyl Ln, respectively. Hydroperoxides of EPA and DHA esters are much less stable than those of ethyl Lo. The peroxide value is not necessarily a good indication of oxidation in these polyenoic acids because a considerable amount of secondary products is formed at the early stage of oxidation. Polymers were found to be major secondary products in these polyenoic esters.     

Pervaporation membranes for ethanol–water mixture prepared by plasma polymerization. III. Perfluorocarbon membranes

Pervaporation membranes for the ethanol–water mixture were prepared by plasma polymerization of tetrafluoroethylene, perfluoropropane, and perfluoropropylene onto porous substrates. The influence of the monomers on the elemental ratio (F/C) of the polymer depositions by X-ray photoelectron spectroscopy was rather small compared with that of the W/FM parameter (W = wattage for plasma excitation, FM = mass flow rate of a monomer). The optical emission spectroscopy indicated the similarity of gaseous species formed in the plasmas. The membranes were found ethanol-permselective, showing separation coefficients (α_EtOH) around 4–7 and a wide range of permeation rates (J), 10–10^?2 kg/m² h, for the 4.8 wt % ethanol solution at 40°C. The α_EtOH of the membranes with thicker depositions could be correlated to the F/C ratios as a measure of membrane hydrophobicity. It was thought that, by making a plot α_EtOH against J values for the perfluorocarbon membranes, they could be classified into three groups on thickness of deposition. The ethanol-separation mechanisms for each group, which may contain four kinds of mass transfer schemes, i.e., distillation through larger pores, flow of sorption layer at the liquid–membrane interface, and diffusions through deposition or substrate, were also discussed.     

Si-C-O glass-like compound/exfoliated graphite composites for negative electrode of lithium ion battery

Two low molecular weight silicone compounds, a cyclic type having vinyl groups and a chain-type having Si-H bonds, a catalyst for curing, and a catalyst regulator were mixed. The mixture was impregnated into exfoliated graphite (EG) by sorption, and cured in air at 200 °C. By this process cross-linked silicone coatings were formed on graphite flakes. The composites of Si-C-O glass-like compounds and EG were synthesized by heat treatment of this precursor at 1000-1400 °C for 1 h in argon. The composites formed at 1000-1300 °C were amorphous by XRD and had practically the same chemical composition: Si 44-45, C 27-29, O 25-26, H < 0.5, all in mass%. The ²⁹Si MAS-NMR spectra indicated that the compound formed at 1000 °C was mainly composed of siloxane bonds and amorphous silica, whereas in the compound formed at 1300°C, Si-C bonds and amorphous silica were predominant. The insertion/extraction characteristics of lithium ions for the electrode prepared with composite:poly(vinylidene fluoride) = 90:10 mass% were examined in 1 mol L⁻¹ LiClO₄ solution of ethylene carbonate:diethyl carbonate = 50:50 vol%. High, 650-700 mA h g⁻¹, capacities and steady cycle performance at 50 mA g⁻¹ were achieved with the composites formed at 1250-1300 °C. Capacities of the composites formed at 1200 °C and lower were initially higher but decreased with increasing number of cycles. The composites formed at 1350 °C showed good cycle performance but the capacity was about 500 mA h g⁻¹ due to the formation of β-SiC. Except for the first cycle, the capacity-potential characteristics were similar to those of hard carbons and the coulomb efficiency was 95-100%. For all the composites the capacity was larger than that of graphite (372 mA h g⁻¹) in the range of 50-200 mA g⁻¹. Due to the large insertion capacity of the first cycle, the efficiency was low (60-70%) at first. By short-circuiting the working electrode to the lithium foil counter electrode for a certain period, the irreversible capacity of the first cycle was almost eliminated. It indicates that direct doping of lithium ions into composites is a promising way to increase the efficiency of the first cycle.     

Synthesis of diameter-controlled carbon nanotubes using centrifugally classified nanoparticle catalysts

Iron-based nanoparticles, centrifugally classified by size, with variation of subnanometer order, have been used for the growth of diameter-controlled carbon nanotubes (CNTs) for the first time via catalytic chemical vapor deposition. The centrifugal classification of nanoparticles is facilitated by fractional precipitations through the sequential addition of ethanol to a hexane solution containing the nanoparticles. Three different nanoparticle sizes were obtained, which have average diameters and standard deviations of 3.9 ± 0.8 nm, 3.3 ± 0.6 nm, and 2.8 ± 0.4 nm. By the classification process of nanoparticles, the standard deviation of the average diameter of the fractionated nanoparticles decreased by around one half of that of the as-synthesized nanoparticles. In addition, we demonstrate a technique for estimating the average diameter of each classified nanoparticle using conventional low-angle X-ray diffraction, without the need for time-consuming TEM observation and analysis. From the three classified nanoparticle sizes, with average diameters of 2.8, 3.3, and 3.9 nm, CNTs with average diameters of 3.1, 3.6, and 4.5 nm were obtained by changing growth temperatures, respectively. Therefore, centrifugally classified nanoparticles are one of the most promising ‘seeds’ for use in the diameter-selective growth of CNTs.     

Preparation of regioisomers of structured TAG consisting of one mole of CLA and two moles of caprylic acid

TAG (MLM) with medium-chain FA (MCFA) at the 1,3-positions and long-chain FA (LCFA) at the 2-position, and TAG (LMM) with LCFA at the 1(3)-position and MCFA at 2,3(1)-positions are a pair of TAG regioisomers. Large-scale preparation of the two TAG regioisomers was attempted. A commercially available FFA mixture (FFA-CLA) containing 9-cis, 11-trans (9c, 11t)- and 10t,12c-CLA was selected as LCFA, and caprylic acid (C₈FA) was selected as MCFA. The MLM isomer was synthesized by acidolysis of acyglycerols (AG) containing two CLA isomers with C₈FA: A mixture of AG-CLA/C₈ FA (1∶10, mol/mol) and 4 wt% immobilized Rhizomucor miehei lipase was agitated at 30°C for 72 h. The ratio of MLM to total AG was 51.1 wt%. Meanwhile, LMM isomer was synthesized by acidolysis of tricaprylin with FFA-CLA: A mixture of tricaprylin/FFA-CLA (1∶2, mol/mol) and 4 wt% immobilized R. miehei lipase was agitated at 30°C for 24 h. The ratio of LMM to total AG was 51.8 wt%. MLM and LMM were purified from 1,968 and 813 g reaction mixtures by stepwise short-path distillation, respectively. Consequently, MLM was purified to 92.3% with 49.1% recovery, and LMM was purified to 93.2% with 52.3% recovery. Regiospecific analyses of MLM and LMM indicated that the 2-positions of MLM and LMM were 95.1 mol% LCFA and 98.3 mol% C₈ FA, respectively. The results showed that a process comprising lipase reaction and short-path distillation is effective for large-scale preparation of high-purity regiospecific TAG isomers.     

Thraustochytrid as a potential source of carotenoids

Thraustochytrids, marine protists whose dominant genera are Thraustochytrium and Schizochytrium, belong to the kingdom Chromista and are known as an industrial source of DHA. We describe here that thraustochytrid strain KH105, isolated as a DHA producer, also accumulates significant levels of β-carotene and xanthophylls including canthaxanthin and astaxanthin. A4-d cultivation using a medium composed of 10% glucose and less than 0.3% of nitrogen sources in a half-concentration of seawater gave an astaxanthin production up to 6.1 mg/L, and canthaxanthin content reached more than 10 mg/L under conditions where a higher concentration of nitrogen sources (6%) was employed. It might be advantageous in mass production systems for these carotenoids to be extracted readily by simply suspending the cells with organic solvents such as acetone and chloroform. Analyses on the morphological and life history features of the KH105 strain revealed that it belongs to the genus Schizochytrium. This particular species of thraustochytrids is thus considered to be a promising source of xanthophylls as well as DHA for use in the food industry.     

Antioxidant effects of chlorophyll and pheophytin on the autoxidation of oils in the dark. II. The mechanism of antioxidative action of chlorophyll

To understand the mechanism of the antioxidant effect of chlorophyll on the autoxidation of oils in the dark, antioxidant activities of several derivatives of chlorophyll were compared. Antioxidant activities were observed in chlorophyll derivatives such as protopor-phyrin methyl ester and its magnesium chelated compound. Porphyrin seems to be an essential chemical structure for the antioxidant activity of chlorophyll. Chlorophyll did not decompose the hydroperoxides, but reduced free radicals such as 1,1-diphenyl-2-picrylhydrazyl. Electron spin resonance spectrum of the π-cation radical was recorded during the oxidation of chlorophyll in methyl linoleate solution. These observations suggest that chlorophyll may act as a hydrogen donor to break the chain reaction.     

The oxidative coupling of methane on alkali- and alkaline earth-phosphate catalysts

The oxidative coupling of methane has been tested over alkali- and alkaline earth-phosphate catalysts at 700 and 775 °C with and without the introduction of a small quantity of tetrachloromethane (TCM) to the feedstream. In general, the conversion of methane was enhanced by the addition of TCM but the effect on selectivity was dependent on the catalyst being examined. The selectivity to C₂ and higher hydrocarbons and that to oxidation products have been shown to have a dependence on the cation radius/charge ratio.